Battery Charger Instructions

The following instructions are for battery chargers supplied after January 2021.

This balance charger (UP600+) is designed for dual channel batteries, Solid State or Lithium Polymer (LiPo). It can charge and storage charge two 2-6S Solid State/LiPo battery packs simultaneously. It has over-voltage, over-current, reverse polarity, and over-temperature protection to ensure maximum safety.

Specifications

Input Voltage: AC 110V or 220V

Charge Output Power: 1200W (600W x2)

Discharge Power: 80W (40W x2)

Charge Current : 5A/10A/15A/20A/25A

Balance Current: 1.5A/cell

Battery Type: Solid State/LiPo

Battery Cell Count: 2-6S (also can charge 2S/3S radio battery)

Working Mode: Balance Charge / Storage

Dimension: 268 x 140 x 127mm

Net Weight: 3.1kg

Features

• Supports charging two 2-6S Solid State/LiPo batteries.
• With an independent radio battery connection port, it supports charging 2S/3S radio batteries. (Only one radio battery can be charged one time.)
• Charging current is adjustable: 5A/10A/15A/20A/25A.
• Two working modes: Balance Charge Mode and Storage Mode.
• Memorizes the last charging current.
• Multiple protection functions: over-voltage, over-current, reverse polarity, and over-temperature protection.

Operating Procedures

1. Power on: Connect to the power source and turn on the power switch. The two-color indicators will illuminate for 2 seconds, and the LCD display screen will show the start-up page for 2 seconds, and then it will enter into the standby page.

2. Battery connection: Please connect your batteries according to the below picture. Make sure the power cables are pushed all the way in. Make sure to use the balancing cable and that each cell voltage is displayed on the charger screen.

3. Setting the charging parameter

1. Press the  button to choose the appropriate current, 5A,10A,15A,20A,25A (Normally, we suggest charging with 1C charge current).
2. Press the  button to choose the mode you need, the default mode is charge mode.
3. Hold  for 2 seconds until you hear a “beep” sound. The two-color indicator will flash, indicating the charger is now in the charging process.
4. Stop: If you want to stop the process, please press button.

Recommended Charge Rates

Solid State Batteries:
20A charge rate

Solid state batteries came standard with all units mid-2021 and are gray in color.

• The solid state batteries have a 22,000mAh capacity.
• The ideal charge rate is 1X the battery’s capacity = 22Ah (1C) 
  • Since the charger’s current is incremental by 5A, charge the battery at the closest setting available (20A)
  • NEVER charge the battery at a higher current than 1X the capacity

LiPo Batteries: 15A charge rate
LiPo batteries came standard for all units prior to mid-2021 and are white in color.

• The LiPo batteries have a 16,000mAh capacity.
• The ideal charge rate is 1X the battery’s capacity = 16Ah (1C)
  • Since the charger’s current is incremental by 5A, charge the battery at the closest setting available (15A)
  • NEVER charge the battery at a higher current than 1X the capacity

Charging Process, Indicate The Battery Level Status

The two-color indicator will show in red color.

The LCD screen will switch the interface display every few seconds, as shown in the picture.

Switch a Solid State Battery and a LiPo Battery

Press the  and  simultaneously for 3 seconds

Storage Mode

If a Solid State Lithium battery is not used for a long time, it’s highly recommended to charge or discharge the battery to 3.70V with the Storage Mode to extend the battery’s life. When the battery voltage is higher than 3.70V per cell, the charger will discharge the battery. Conversely, when the battery voltage is lower than 3.70V per cell, the charger will charge the battery under the Storage Mode.

Press the “Mode” button, choose the Storage mode.

Long press the “Start/Stop” button, enter into the Storage mode.

Important Information Tips

When the charger appear below abnormal situations, the two-color indicators will flash in red, and LCD display screen will appear fault message, please refer to below specific message notification and reasons.

Note: the two-color indicators will flash in red, and LCD screen will appear fault message.

Important Warning and Safety Instruction

⚠ These warnings and safety instructions are particularly important. Please follow the instructions for maximum safety. Otherwise, the charger and the battery can be damaged or at worst it can catch fire.

1. Never leave the charger unattended when it is connected to its power supply. If any malfunction is found, TERMINATE THE PROCESS AT ONCE and refer to the operation manual.
2. Keep the charger away from dust, moisture, rain, heat, direct sunshine, and vibration.
3. The input voltage is AC 110V or AC 220V, before connecting to the power source, please keep its input voltage is the same as the charger.
4. The default battery type is Solid State battery type with charge mode. Before connecting the battery, please keep the battery type comply with the charger setting.

Warranty And Service

We guarantee this product to be free of manufacturing and assembly defects for a period of one year from the time of purchase. The warranty only applies to material or operational defects, which are present at the time of purchase. During that period, we will repair or replace free of service charge for products deemed defective due to those causes. You will be required to produce proof of purchase (invoice or receipt). This warranty is not valid for any damage or subsequent damage arising as a result of misuse, modification, or as a result of failure to observe the procedures outlined in this manual.